자유게시판

Reasons Your fiat bravo key 500 Key Fob Won't Work

A fiat 500 electric key 500 key fob makes it easy to open doors and start your vehicle. There are a myriad of reasons the fob won't work. These include a dead coin battery damage to the receiver module, water problems, and interference.

This listing is for an NEW replacement fiat punto key fob 500 replacement key uk - http://it-viking.ch, Flip Key Remote - similar to the Ilco brand that needs to be professionally programmed by a local automotive locksmith (click here to search for a Locksmith Search). It comes with lock, unlock and trunk buttons.

Dead Coin Battery

A dead battery is the main reason for your 500 key fob being inoperative. Modern key fobs only have an operating range that is limited and must be within a few inches of your vehicle to work. If you're not close to your vehicle, and you press the key fob button the car won't respond and will display the "Key Fob Not Detected" message in the instrument cluster.

If this happens, replace the coin-cell battery (Part Number CR2032) with a new battery of a reputable brand like Panasonic Duracell or Energizer. They are available at your local hardware store, or online.

After you've replaced the battery of your coin cell you can test it by standing close to your fiat 500 duplicate key 500 and pressing the buttons. The car will flash its parking lights, and the key fob will operate the lock and unlock switches.

If your key fob does not work after replacing the battery, it might be water damage that is preventing it from communicating with the module in your vehicle. Water damage can happen in a number of ways, from small splashes to submerging the fob in salt water at the beach. If you suspect your fob has been exposed to water, put it in a dry rice bag to draw the moisture out. If this doesn't work, your fob is likely to need to be reset by a professional locksmith or dealer.

Water Damage

While the fob has some rubber seals to keep water from the chip's electronic circuit it, submerging it in the ocean or washing it in a machine can cause water damage. Saltwater can be particularly harmful to the circuit board of the fob which causes it to short out and eventually die. It's not good to soak the fob in water but don't give up even if you accidentally drop the fob in water or fail to remove it from your pocket.

First take the battery off the fob. Before replacing the battery clean the electronic chip with isopropyl or a similar product. Check the fob again to verify if it's functioning. If the key isn't working, it may have to be programmed again. This is usually handled by an auto locksmith or dealer.

If the key is more recent and was not programmed to your vehicle it is likely to need to be replaced completely. This is a simple procedure which can be accomplished by a professional locksmith for automotive use. The locksmith must cut the key to match the ignition of your vehicle. The locksmith also needs to reprogram your fob into the vehicle's system. This is a low-cost and quick process that could be completed the same day.

Receiver Module Issues

Your 500 key fob might not function because it's out of range. The remote has a range of 30 feet. So should you be too far from your car, it won't respond to your commands. It can be solved by moving closer to your vehicle until it starts responding.

If your fob doesn't work after replacing the coin battery, also known as a "button", "watch" or "button" it could be due to an issue with the circuit board inside. In the majority of cases, reprogramming your fob will solve the issue. You can find the instructions on how to do this for the majority of vehicles by searching YouTube or reading the owner's manual.

It is sometimes necessary to replace the clips made of metal that hold the coin batteries in their place. If they lose tension, it could prevent your coin battery from sitting properly, causing your remote to malfunction.

In rare cases the fob can become out of connection with your vehicle as a result due to hardware or software issues. You can fix this problem by visiting your local dealer or auto-locksmith to reprogram your key fob. In some cases they might need to install the software again in your body control module as well.

Interference

In addition to a dead battery on a coin, the key fob may not be receiving or transmitting the signal due to interference. This can occur when the key fob is in close proximity to a radio transmitter, such as a cell phone or radar detector. The key fob may not function due to a poor connection with the buttons water damage or damage to the internal chips.

If your key fob suddenly stopped working, or you have tried everything at home to solve the issue (e.g. replacing batteries, reprogramming or using the spare key fob, you might have a faulty receiver module on your 500. The receiver module is situated under the dash and receives the radio frequency signals from the key fob. It converts them to electronic commands that the vehicle interprets.

There is a straightforward method to reset the 500's on-board system including the keyfob. Disconnect the battery of 12 volts for approximately 15 minutes by removing the negative cable first then the positive cable. Reconnect the battery. This will remove any remaining electricity and restart the car's computers, which could allow you to the key fob to function again. If the issue persists it is recommended that you consult an expert technician. They'll be able diagnose the exact cause of your problem.